Axia Fusion Help Documents
- 46 Articles
- Updated on Aug 4, 2025
- Published on Aug 4, 2025
Kit Parts and Availability Availability is accurate as of August 2025
- Published on Jul 9, 2025
Scope Occasionally, we are asked if we sell boxes and foam for a Fusion console for users who need to send an entire console to us for repair or replacement. While we still carry boxes large enough to fit a full console, we no longer carry the prop...
- Published on Dec 13, 2024
Scope Fusion non-motorized modules are equipped with black fader knobs, while motorized modules come with silver conductive knobs. However, knobs are also available in red, blue, and gray. Replacement Knobs The default knobs that came with your F...
- Published on Dec 13, 2024
Scope Axia Studio Engine (v2.5x and higher) and Axia Quasar Engine are equipped with the capability to deliver Omnia 3 style processing for monitoring paths, including headphone feeds and monitor feeds. When the integrated headphone processing is ...
- Published on Dec 13, 2024
Scope This document covers how to provide power to a Fusion (or Element) console, without using a PowerStation or an Element Power Supply + GPIO Node. The Alternative Power Supply A Fusion or Element console can also be powered by an Axia Console...
- Updated on Jun 8, 2026
- Published on Dec 13, 2024
Scope This document provides the part numbers for the power cables needed to power a Fusion (or Element) console when using either an Axia Console Power Supply (2001-00375) or an Axia Console Backup Power Supply (2001-00277). Both of these PSU cha...
- Published on Dec 13, 2024
Scope You can add virtual faders to most Axia consoles. This document covers the process of adding virtual faders to Fusion consoles or to Element consoles with a Powerstation, where the software version is 3.0 or higher. Description Customers of...
- Published on Dec 13, 2024
Scope This document covers configurations of Show profiles in an Element or Fusion console, which could cause a brief audio drop out when a show profile is loaded. Description The customer states that they get a brief "drop" in the audio every ti...
- Published on Dec 13, 2024
Scope This document covers the process of verifying the mechanical and electrical status of individual buttons on a Fusion console without respect to the actual function of the button. Although we're demonstrating Fusion, these examples work the sa...
- Published on Dec 13, 2024
Scope The document covers the steps needed to enable the Fader Start mode on Element, Fusion, Quasar or IQ Consoles. Description Fader start is a setting that allows the position of the Fader to control the ON and OFF state. There are three ope...
- Published on Dec 13, 2024
Scope Fusion non-motorized modules are equipped with black fader knobs, while motorized modules come with silver conductive knobs. However, knobs are also available in red, blue, and gray. The knobs listed here differ from what shipped with y...
- Published on Dec 13, 2024
Scope This document covers the setup and use of the count-up timer in Fusion and Element consoles. Description Fusion and Element have two timers that are presented on the main display. This help document covers the setup and use of the coun...
- Published on Dec 13, 2024
Scope The intent of this document is to cover the configuration of an Element or Fusion 2-fader call control module to control a Telos VX System. It presumes that the VX system has been configured, has extensions registered with a SIP server, Show...
- Published on Dec 13, 2024
Scope This document goes over the testing procedure for the following Fusion modules: 2001-00335 - Fusion 10-Button SmartSwitch 2001-00336 - Fusion 5-Button SmartSwitch The Procedure In a non-static area, use a small flat head...
- Published on Dec 13, 2024
Scope Axia consoles allow for simple ways to record your host and phone calls to separate channels. One method is by configuring a Vmode. This document aims to discuss how to configure your console to achieve this. Note that this can only be done...
- Updated on Oct 5, 2026
- Published on Dec 13, 2024
Scope Some User Panel features in Pathfinder Core PRO require an updated version of the Fusion console software that runs on your Engine or Power Station. This document describes how to obtain and install the update. This update may also be require...
- Published on Dec 13, 2024
Scope This document covers replacing the blank and icon translucent button caps on all Fusion modules, including Accessory modules: 2001-00328-000 Fusion Monitor/Navigation Module 2001-00329-000 Fusion 4-Fader Module (S) 2001-00330-000 Fus...
- Published on Dec 13, 2024
Scope This article applies specifically to Fusion consoles; however, other consoles or displays may have similar film covering them during manufacturing and shipment. Description The customer writes in that they just received their Fusion console...
- Published on Dec 13, 2024
Scope This document pertains to the bezel that surrounds the On and Off buttons on the following Fusion modules: 2001-00329-000 Fusion 4-Fader Module (S) 2001-00330-000 Fusion Motorized 4-Fader Module (S) 2001-00331-000 Fusion Call Control...
- Published on Dec 13, 2024
Scope This document covers the icons that are displayed on the overbridge of a Fusion console. Description Some of the icons displayed on a Fusion console are specific to the type of source that you have defined. For example, no Phone icons will ...
- Published on Dec 13, 2024
Scope This document explains why a Fusion surface overbridge is showing an up or down arrow. The Arrow What It Means The up arrow (or a down arrow) is an indication that the fader value in the engine is different from the physical fader pos...
- Published on Dec 13, 2024
Scope This document is for Fusion console systems running on the Fanless Studio Engine or Powerstation. Description Once the Fusion surface's Ethernet interface is paired to a console engine, it will no longer advertise itself to the automatic di...
- Published on Dec 13, 2024
Scope This document applies to both Fusion and Element consoles and covers cases where the Control Room Monitor volume can not be changed. Description There is generally one of three things that will prevent the Control Room Monitor Volume from b...
- Published on Dec 13, 2024
Scope This document covers replacing the black button caps found on the Monitor/Navigation and Call Controller modules: 2001-00328-000 Fusion Monitor/Navigation Module 2001-00379-000 Fusion Navigation + 2-Fader Module 2001-00331-...
- Published on Dec 13, 2024
Scope The intent of this document is to cover the configuration of an Element or Fusion to control a Telos VX, Hx6, or iQ6 System from the input channel without a 2-Fader Call Control Module . It presumes that the hybrid/phone system has been conf...
- Published on Dec 13, 2024
Scope The status page on the Fusion or Element says 100% - Is this a problem. Description The short answer is that if everything seems to otherwise be working, then no, it's not a problem. If you look at the Status page on your Fusion or Element...
- Published on Dec 13, 2024
Scope This article describes how to remove or replace a Fusion console module. This can also be applied to Element as the hardware is very similar. Step 1: Remove Retaining Screws Use the 2.5 mm hex wrench to remove the retaining screws at the ...
- Published on Dec 13, 2024
SCOPE This applies to the Headphone and Control Room Monitor volume controls on both Element and Fusion consoles. The pictures shown here are from an Element console. This encoder fairly simple to test and replace. Once the module is removed,...
- Published on Dec 13, 2024
Scope This document covers both the Element and Fusion console, where you use the number pad on the console Master module for dialing. Description When you dial a telephone number from an Element or Fusion console, the numbers you dial display in...
- Published on Dec 13, 2024
SEE THE ELEMENT PROCEDURE: The procedure for cleaning and lubricating Fusion faders is identical to the Element procedure, which can be found here.
- Published on Dec 13, 2024
Scope This article discusses the removal / replacement of a Fusion Overbridge Module only. This procedure does not apply to Element. Step 1: Open the Overbridge Hinge open the overbridge as shown. Step 2: Locate and Disconnect the Module(s)...
- Published on Dec 13, 2024
Scope This document covers the different operating modes of User Modules mounted in a Fusion or Element console. There are two basic modules shown here. There is an LCD version that can display text and a Film Cap version, which would require the ...
- Published on Feb 11, 2025
Scope The intent of this document is to cover the configuration of an Element or Fusion 2-fader call control module to control a Legacy Telos Nx or TWO-x-12 Hybrid System. It presumes that the Nx12 or TWO-x-12 has been configured, has ready lines ...
- Published on Feb 11, 2025
Scope The intent of this document is to cover the configuration of an Element or Fusion 2-fader call control module to control a Telos Hx6 or iQ6 Hybrid System. It presumes that the hybrid system has been configured, has ready lines (dots show on ...
- Published on Dec 13, 2024
SCOPE This document covers the setup of the Fusion fader accessory module with part number 2001-00419-000. DESCRIPTION We will cover the configuration of the Fusion fader accessory module. We assume that you have already installed this acces...
- Published on Dec 13, 2024
Scope How to use the VMixer in the Fusion Engine, Powerstation, or Telos iPort to modify the audio sent back to a codec or phone caller from an Axia console. Description Most of the time, the standard mix minus from an Axia console engine's backf...
- Published on Dec 13, 2024
Scope These are several steps needed to enable the AUX busses on a Fusion or Element console. They are detailed here. Depending on your version, the screens may vary slightly. Enable the Sources From the main web page of your console, click ...
- Published on Dec 13, 2024
Scope This applies to Element and Fusion consoles. For grounding information on QOR consoles, click here . The Stud As our Fusion and Element manuals state, "(Each console) must be connected to a grounded metal permanent wiring system or other ...
- Published on Dec 13, 2024
Scope Both Fusion and Element consoles have options for a "custom" backfeed that can override the pre-programmed choices. We cover the configuration of the custom options here. Note that these steps and images apply only to Fusion and Element conso...
- Published on Dec 13, 2024
Scope This article discusses using Legacy hybrids with analog i/o with a Fusion console system. It can also be applied to Element, Quasar, and iQ series console systems. Description The Telos VX, Hx6, iQ6, and the Legacy Nx12 can interface with a...
- Published on Dec 13, 2024
Scope This article applies to the Fusion and Element console systems using the Studio Engine or Powerstation platforms running version 3 or higher. Description Sometimes we need on-air contribution from a console in another control room. The easi...
- Updated on Dec 17, 2024
- Published on Dec 16, 2024
Scope This document talks about the fader option "Fader Start with Arm." This feature is available in Element, Fusion, Quasar and all QOR consoles. For Quasar consoles, this option is available with both XR and SR modules. For more detailed infor...
- Published on Dec 31, 2024
Scope This Corrective Field Action (CFA) impacts the following products: 2001-00305 - Zephyr iPort (FANLESS) MPEG Gateway 2001-00378 - Zephyr iPort MPEG Gateway + Content Delay 2001-00306 - Axia Studio Mix Engine (FANLESS) 2001-...
- Published on Dec 30, 2024
Scope This is provided for historical information purposes. Generally you would never need to change these jumpers but for ONE exception on Fusion modules. Description Fusion (and Element) fader modules have always had option jumpers that defined...
- Published on Dec 30, 2024
Scope This document offers steps to fix the issues after uploading a backup from an older console to a newer console or even bringing up an backup console. Some of the faders might show inactive. Description The problem is that sometimes the cons...
- Published on Dec 30, 2024
Scope This document explains the basics of the RPL Attributes page found in the Engine of Element, Fusion, and Quasar console engines. In Quasar Engine, the RPL Attributes page is renamed to DSP Parameters, as shown here. The information displa...